※万向节注意事项：
1调整时不能超过规定的角度15度
2如超过此极限心轴易磨损或断裂
3工作时应经常加润滑油脂
※Note of cardan Joint
1.Do not set the angle to more than the specifled l5 degrees.
2.If the limit is exceeded，the shaft will be easy to wear or break.
3.During work，lubrication should be added frequently.
注：ER8和C5小间距为13，ER11和C6小间距为18，ER16和C9小间距为26，ER20和C12小间距为28
SU100×165 | SU120×200 | SU120×300 | SU160×450 | SU220×360 | SU250×500 | SU170X200 | SU300X400 | SU400X550 | SU450X550 | SU150X800 | SU300X1000 |
ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 | ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 | ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 | ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 | ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 | ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 | ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 | ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 | ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 | ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 | ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 | ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 |
1∶1 1∶2 | 1∶1 1∶2 | 1∶1 1∶2 | 1∶1 1∶2 | 1∶1 1∶2 | 1∶1 1∶2 | 1∶1 1∶2 | 1∶1 1∶2 | 1∶1 1∶2 | 1∶1 1∶2 | 1∶1 1∶2 | 1∶1 1∶2 |
13 18 26 28 | 13 18 26 28 | 13 18 26 28 | 13 18 26 28 | 13 18 26 28 | 13 18 26 28 | 13 18 26 28 | 13 18 26 28 | 13 18 26 28 | 13 18 26 28 | 13 18 26 28 | 13 18 26 28 |
100×165 | 120×200 | 120×300 | 160×450 | 220×360 | 250×500 | 170×200 | 300×400 | 400×550 | 450×550 | 150×800 | 300×1000 |
2-8 | 2-12 | 4-16 | 4-16 | 6-14 | 4-18 | 2-12 | 4-16 | 4-18 | 4-18 | 4-18 | 4-18 |