详细介绍

柱式液位指示器

型号

主要规格

安装端

玻璃纤维加固聚酰胺基（PA）高科技聚合体，黑色。

支架

铝制，本色。

带刻度的反差屏

白色喷涂铝。安装前可取出便于加入液位线和文字。

浮子

Technopolymer, black colour, with a built-in magnetic element to activate the electric contact when the float reaches the contact threshold located at about 55 mm above the axis of the lower screw (data referred to mineral oil type CB68, according to ISO 3498, temperature 23°C).

Bracket with sensors

Watertight glass-fibre reinforced polyamide based (PA) technopolymer, black colour.

旋转接头

内置电缆接头和触点固定座。前部或轴向输出（上部或下部）溅水防护(保护等级为IP65级，参见表 EN 60529 表.

标准型号

See configuration table.

柱式液位指示器通用信息

特征及性能

由于连接器的侧面输出，HCK-E-ST/STL 液位指示器在zui低液触发位传感器。

技术参数)

In laboratory tests carried out for a relatively limited time with the following liquids at a temperature of 23° C: mineral oil type CB68 (according to ISO 3498) for HCK, mineral oil type CB68 (according to ISO 3498) water or water/glycol-based solutions ( 50%) for HCK-GL, the resistance values were much higher than 35 bar.

需接触其它液体或需在不同的压力和温度下使用指示器，请ELESA技术部，

在任何情况下，均建议根据实际工作情况验证产品的适用性。

电气特征

zui低液位电子传感器的功能

NO: 到达zui低液位电触头关闭。
NC: 电触点在达到zui低液位。
SW (change-over electrical contact): the electrical contact switches between the two terminals.

电气特性	zui低液位传感器
压力介质	AC/DC
电触点	NO常开 NC常闭可切换触点
zui高应用电压	NO: 140 Vac, 200 Vdc NC: 140 Vac, 150 Vdc SW: 140 Vac, 150 Vdc
zui大切换电流	1 A
zui大电流	NO: 1.2A NC: 2A SW: 2A
zui大交换功率	NO: 10 Va NC: 20 Va SW: 20 Va
Cable gland	Pg 7 (用于连套直径为Ø 6 或 7 mm的电缆)
导体截面	Max. 1.5 mm²
勿将此指示器靠近磁场安装

Functioning of the MAX temperature sensor

NO: 电触点在达到zui低液位时关闭/或温度达到预设值（80°C）时。
NC: 电触点在达到zui低液位时关闭/或温度达到预设值（80°C）时。

电气特性	zui高传感器温度
压力介质	AC/DC
电触点	NO常开 NC常闭
电压 zui大电流	250 Vac - 2 A	电阻负载
	115 Vac- 3A
	24 Vdc - 3 A
	12 Vdc - 4 A
zui小电流	50 mA
Cable gland	Pg 7 (用于连套直径为Ø 6 或 7 mm的电缆)
导体截面	Max. 1.5 mm²

电子温度探针的功能

温度传感器的工作原理是测量铂元件的电阻变化：100 ohm = 0°C,138.4 ohm = 100°C。

在较小的温度范围内，温度（T）与电阻（R）间的函数近似于直线：例如，假设0℃至100℃的温度范围内为直线，则50℃时的误差为0.4℃。

为精确测量，须将电阻设为直线，以给出准确温度。温度标准（ITS-90）是对电阻与温度间函数的定义。图示为直接测定触头电阻值的电阻与温度间的函数，该函数通过实验室试验测得。我们建议设置补偿热耗散及电缆电阻的系统。

温度变化1℃，电阻将变化0.384ohm，因此，测量电阻时，即便是出现小误差，也可能导致温度测量上的大误差。

由于信号电平较低，须保持所有线缆远离电缆、电动机、开关装置及其它可能发出电噪声的装置。使用一端带屏蔽装置的屏蔽电缆，可减少干扰。

所用电缆较长时，须检查测量装置是否能控制该电缆的电阻。

电气特性	温度探针
压力介质	AC/DC
zui大电流	1mA
Cable gland	Pg 7 (用于连套直径为Ø 6 或 7 mm的电缆)
导体截面	Max. 1.5 mm²
勿将此指示器靠近磁场安装

其它型号

按需提供的特殊型号

柱式液位观察窗，PMMA制成，用于zui高70°C的使用场合。
带有镀镍黄铜螺纹的螺钉，位于产品较低处的安装端，用于保养时抽出指示器的操作。
推入式注油塞
Special screw with nickel-plated brass tap to be fitted to the lower assembly end for any maintenance operation requiring the indicator exclusion.

应用说明

接头安装说明

拧松传感器上的固定螺钉，取下传感器托架，拧开电缆护座，将接头从托架上取下。
See Fig.3 to proceed with the wiring according to the chosen product.
将接触支座压入所需位置的接触接头，完成安装。
用轴向固定螺钉将接头固定在传感器托架上，随后拧紧电缆护座。

HCK-E
带zui低液位电子传感器
HCK-E-ST
带zui低液位和zui高温度电子传感器
HCK-E-STL
带电控zui低液位传感器和电子温度探针

HCK-E with MIN level electrical sensor

代码	说明	f	L	e	d'_-0.2	f'	C# [Nm]	重量
113011	HCK.127-ZN-M12-NBR-PC-P-E-NC	127	164	56	12.5	127±0.5	12	231
113009	HCK.127-ZN-M12-NBR-PC-P-E-NO	127	164	56	12.5	127±0.5	12	231
113013	HCK.127-ZN-M12-NBR-PC-P-E-SW	127	164	56	12.5	127±0.5	12	231
114011	HCK.176-ZN-M12-NBR-PC-P-E-NC	176	213	105	12.5	176±0.5	12	261
114009	HCK.176-ZN-M12-NBR-PC-P-E-NO	176	213	105	12.5	176±0.5	12	261
114013	HCK.176-ZN-M12-NBR-PC-P-E-SW	176	213	105	12.5	176±0.5	12	261
116111	HCK.254-ZN-M12-NBR-PC-P-E-NC	254	291	183	12.5	254±0.5	12	309
116109	HCK.254-ZN-M12-NBR-PC-P-E-NO	254	291	183	12.5	254±0.5	12	309
116113	HCK.254-ZN-M12-NBR-PC-P-E-SW	254	291	183	12.5	254±0.5	12	309
117011	HCK.381-ZN-M12-NBR-PC-P-E-NC	381	418	310	12.5	381±0.5	12	388
117009	HCK.381-ZN-M12-NBR-PC-P-E-NO	381	418	310	12.5	381±0.5	12	388
117013	HCK.381-ZN-M12-NBR-PC-P-E-SW	381	418	310	12.5	381±0.5	12	388
117911	HCK.508-ZN-M12-NBR-PC-P-E-NC	508	545	437	12.5	508±0.5	12	466
117909	HCK.508-ZN-M12-NBR-PC-P-E-NO	508	545	437	12.5	508±0.5	12	466
117913	HCK.508-ZN-M12-NBR-PC-P-E-SW	508	545	437	12.5	508±0.5	12	466
113141	HCK.127-ZN-M12-FKM-PC-P-E-NC	127	164	437	12.5	127±0.5	12	231
113139	HCK.127-ZN-M12-FKM-PC-P-E-NO	127	164	437	12.5	127±0.5	12	231
113143	HCK.127-ZN-M12-FKM-PC-P-E-SW	127	164	437	12.5	127±0.5	12	231
114141	HCK.176-ZN-M12-FKM-PC-P-E-NC	176	213	437	12.5	176±0.5	12	261
114139	HCK.176-ZN-M12-FKM-PC-P-E-NO	176	213	437	12.5	176±0.5	12	261
114143	HCK.176-ZN-M12-FKM-PC-P-E-SW	176	213	437	12.5	176±0.5	12	261
116241	HCK.254-ZN-M12-FKM-PC-P-E-NC	254	291	437	12.5	254±0.5	12	309
116239	HCK.254-ZN-M12-FKM-PC-P-E-NO	254	291	437	12.5	254±0.5	12	309
116243	HCK.254-ZN-M12-FKM-PC-P-E-SW	254	291	437	12.5	254±0.5	12	309
117151	HCK.381-ZN-M12-FKM-PC-P-E-NC	381	418	437	12.5	381±0.5	12	388
117149	HCK.381-ZN-M12-FKM-PC-P-E-NO	381	418	437	12.5	381±0.5	12	388
117153	HCK.381-ZN-M12-FKM-PC-P-E-SW	381	418	437	12.5	381±0.5	12	388
118061	HCK.508-ZN-M12-FKM-PC-P-E-NC	508	545	437	12.5	508±0.5	12	466
118059	HCK.508-ZN-M12-FKM-PC-P-E-NO	508	545	437	12.5	508±0.5	12	466
118063	HCK.508-ZN-M12-FKM-PC-P-E-SW	508	545	437	12.5	508±0.5	12	466
113159	HCK.127-ZN-M12-FKM-PC-P-E-HT-NC	127	164	437	12.5	127±0.5	12	231
113157	HCK.127-ZN-M12-FKM-PC-P-E-HT-NO	127	164	437	12.5	127±0.5	12	231
113161	HCK.127-ZN-M12-FKM-PC-P-E-HT-SW	127	164	437	12.5	127±0.5	12	231
114159	HCK.176-ZN-M12-FKM-PC-P-E-HT-NC	176	213	437	12.5	176±0.5	12	261
114157	HCK.176-ZN-M12-FKM-PC-P-E-HT-NO	176	213	437	12.5	176±0.5	12	261
114161	HCK.176-ZN-M12-FKM-PC-P-E-HT-SW	176	213	437	12.5	176±0.5	12	261
116259	HCK.254-ZN-M12-FKM-PC-P-E-HT-NC	254	291	437	12.5	254±0.5	12	309
116257	HCK.254-ZN-M12-FKM-PC-P-E-HT-NO	254	291	437	12.5	254±0.5	12	309
116261	HCK.254-ZN-M12-FKM-PC-P-E-HT-SW	254	291	437	12.5	254±0.5	12	309
117169	HCK.381-ZN-M12-FKM-PC-P-E-HT-NC	381	418	437	12.5	381±0.5	12	388
117167	HCK.381-ZN-M12-FKM-PC-P-E-HT-NO	381	418	437	12.5	381±0.5	12	388
117171	HCK.381-ZN-M12-FKM-PC-P-E-HT-SW	381	418	437	12.5	381±0.5	12	388
118079	HCK.508-ZN-M12-FKM-PC-P-E-HT-NC	508	545	437	12.5	508±0.5	12	466
118077	HCK.508-ZN-M12-FKM-PC-P-E-HT-NO	508	545	437	12.5	508±0.5	12	466
118081	HCK.508-ZN-M12-FKM-PC-P-E-HT-SW	508	545	437	12.5	508±0.5	12	466
113053	HCK.127-ZN-M12-NBR-GL-P-E-NC	127	164	437	12.5	127±0.5	12	231
113051	HCK.127-ZN-M12-NBR-GL-P-E-NO	127	164	437	12.5	127±0.5	12	231
113055	HCK.127-ZN-M12-NBR-GL-P-E-SW	127	164	437	12.5	127±0.5	12	231
114053	HCK.176-ZN-M12-NBR-GL-P-E-NC	176	213	437	12.5	176±0.5	12	261
114051	HCK.176-ZN-M12-NBR-GL-P-E-NO	176	213	437	12.5	176±0.5	12	261
114055	HCK.176-ZN-M12-NBR-GL-P-E-SW	176	213	437	12.5	176±0.5	12	261
116153	HCK.254-ZN-M12-NBR-GL-P-E-NC	254	291	437	12.5	254±0.5	12	309
116151	HCK.254-ZN-M12-NBR-GL-P-E-NO	254	291	437	12.5	254±0.5	12	309
116155	HCK.254-ZN-M12-NBR-GL-P-E-SW	254	291	437	12.5	254±0.5	12	309
117053	HCK.381-ZN-M12-NBR-GL-P-E-NC	381	418	437	12.5	381±0.5	12	388
117051	HCK.381-ZN-M12-NBR-GL-P-E-NO	381	418	437	12.5	381±0.5	12	388
117055	HCK.381-ZN-M12-NBR-GL-P-E-SW	381	418	437	12.5	381±0.5	12	388
117953	HCK.508-ZN-M12-NBR-GL-P-E-NC	508	545	437	12.5	508±0.5	12	466
117951	HCK.508-ZN-M12-NBR-GL-P-E-NO	508	545	437	12.5	508±0.5	12	466
117955	HCK.508-ZN-M12-NBR-GL-P-E-SW	508	545	437	12.5	508±0.5	12	466
113185	HCK.127-ZN-M12-FKM-GL-P-E-NC	127	164	437	12.5	127±0.5	12	231
113183	HCK.127-ZN-M12-FKM-GL-P-E-NO	127	164	437	12.5	127±0.5	12	231
113187	HCK.127-ZN-M12-FKM-GL-P-E-SW	127	164	437	12.5	127±0.5	12	231
114185	HCK.176-ZN-M12-FKM-GL-P-E-NC	176	213	437	12.5	176±0.5	12	261
114183	HCK.176-ZN-M12-FKM-GL-P-E-NO	176	213	437	12.5	176±0.5	12	261
114187	HCK.176-ZN-M12-FKM-GL-P-E-SW	176	213	437	12.5	176±0.5	12	261
116285	HCK.254-ZN-M12-FKM-GL-P-E-NC	254	291	437	12.5	254±0.5	12	309
116283	HCK.254-ZN-M12-FKM-GL-P-E-NO	254	291	437	12.5	254±0.5	12	309
116287	HCK.254-ZN-M12-FKM-GL-P-E-SW	254	291	437	12.5	254±0.5	12	309
117195	HCK.381-ZN-M12-FKM-GL-P-E-NC	381	418	437	12.5	381±0.5	12	388
117193	HCK.381-ZN-M12-FKM-GL-P-E-NO	381	418	437	12.5	381±0.5	12	388
117197	HCK.381-ZN-M12-FKM-GL-P-E-SW	381	418	437	12.5	381±0.5	12	388
118105	HCK.508-ZN-M12-FKM-GL-P-E-NC	508	545	437	12.5	508±0.5	12	466
118103	HCK.508-ZN-M12-FKM-GL-P-E-NO	508	545	437	12.5	508±0.5	12	466
118107	HCK.508-ZN-M12-FKM-GL-P-E-SW	508	545	437	12.5	508±0.5	12	466
113203	HCK.127-ZN-M12-FKM-GL-P-E-HT-NC	127	164	437	12.5	127±0.5	12	231
113201	HCK.127-ZN-M12-FKM-GL-P-E-HT-NO	127	164	437	12.5	127±0.5	12	231
113205	HCK.127-ZN-M12-FKM-GL-P-E-HT-SW	127	164	437	12.5	127±0.5	12	231
114203	HCK.176-ZN-M12-FKM-GL-P-E-HT-NC	176	213	437	12.5	176±0.5	12	261
114201	HCK.176-ZN-M12-FKM-GL-P-E-HT-NO	176	213	437	12.5	176±0.5	12	261
114205	HCK.176-ZN-M12-FKM-GL-P-E-HT-SW	176	213	437	12.5	176±0.5	12	261
116303	HCK.254-ZN-M12-FKM-GL-P-E-HT-NC	254	291	437	12.5	254±0.5	12	309
116301	HCK.254-ZN-M12-FKM-GL-P-E-HT-NO	254	291	437	12.5	254±0.5	12	309
116305	HCK.254-ZN-M12-FKM-GL-P-E-HT-SW	254	291	437	12.5	254±0.5	12	309
117213	HCK.381-ZN-M12-FKM-GL-P-E-HT-NC	381	418	437	12.5	381±0.5	12	388
117211	HCK.381-ZN-M12-FKM-GL-P-E-HT-NO	381	418	437	12.5	381±0.5	12	388
117215	HCK.381-ZN-M12-FKM-GL-P-E-HT-SW	381	418	437	12.5	381±0.5	12	388
118123	HCK.508-ZN-M12-FKM-GL-P-E-HT-NC	508	545	437	12.5	508±0.5	12	466
118121	HCK.508-ZN-M12-FKM-GL-P-E-HT-NO	508	545	437	12.5	508±0.5	12	466
118125	HCK.508-ZN-M12-FKM-GL-P-E-HT-SW	508	545	437	12.5	508±0.5	12	466

代码	说明	f	L	e	d'_-0.2	f'	C# [Nm]	重量
113311	HCK.127-SST-M12-NBR-PC-P-E-NC	127	164	437	12.5	127±0.5	12	231
113309	HCK.127-SST-M12-NBR-PC-P-E-NO	127	164	437	12.5	127±0.5	12	231
113313	HCK.127-SST-M12-NBR-PC-P-E-SW	127	164	437	12.5	127±0.5	12	231
114281	HCK.176-SST-M12-NBR-PC-P-E-NC	176	213	437	12.5	176±0.5	12	261
114279	HCK.176-SST-M12-NBR-PC-P-E-NO	176	213	437	12.5	176±0.5	12	261
114283	HCK.176-SST-M12-NBR-PC-P-E-SW	176	213	437	12.5	176±0.5	12	261
116391	HCK.254-SST-M12-NBR-PC-P-E-NC	254	291	437	12.5	254±0.5	12	309
116389	HCK.254-SST-M12-NBR-PC-P-E-NO	254	291	437	12.5	254±0.5	12	309
116393	HCK.254-SST-M12-NBR-PC-P-E-SW	254	291	437	12.5	254±0.5	12	309
117301	HCK.381-SST-M12-NBR-PC-P-E-NC	381	418	437	12.5	381±0.5	12	388
117299	HCK.381-SST-M12-NBR-PC-P-E-NO	381	418	437	12.5	381±0.5	12	388
117303	HCK.381-SST-M12-NBR-PC-P-E-SW	381	418	437	12.5	381±0.5	12	388
118211	HCK.508-SST-M12-NBR-PC-P-E-NC	508	545	437	12.5	508±0.5	12	466
118209	HCK.508-SST-M12-NBR-PC-P-E-NO	508	545	437	12.5	508±0.5	12	466
118213	HCK.508-SST-M12-NBR-PC-P-E-SW	508	545	437	12.5	508±0.5	12	466
113443	HCK.127-SST-M12-FKM-PC-P-E-NC	127	164	437	12.5	127±0.5	12	231
113441	HCK.127-SST-M12-FKM-PC-P-E-NO	127	164	437	12.5	127±0.5	12	231
113445	HCK.127-SST-M12-FKM-PC-P-E-SW	127	164	437	12.5	127±0.5	12	231
114421	HCK.176-SST-M12-FKM-PC-P-E-NC	176	213	437	12.5	176±0.5	12	261
114419	HCK.176-SST-M12-FKM-PC-P-E-NO	176	213	437	12.5	176±0.5	12	261
114423	HCK.176-SST-M12-FKM-PC-P-E-SW	176	213	437	12.5	176±0.5	12	261
116531	HCK.254-SST-M12-FKM-PC-P-E-NC	254	291	437	12.5	254±0.5	12	309
116529	HCK.254-SST-M12-FKM-PC-P-E-NO	254	291	437	12.5	254±0.5	12	309
116533	HCK.254-SST-M12-FKM-PC-P-E-SW	254	291	437	12.5	254±0.5	12	309
117441	HCK.381-SST-M12-FKM-PC-P-E-NC	381	418	437	12.5	381±0.5	12	388
117439	HCK.381-SST-M12-FKM-PC-P-E-NO	381	418	437	12.5	381±0.5	12	388
117443	HCK.381-SST-M12-FKM-PC-P-E-SW	381	418	437	12.5	381±0.5	12	388
118351	HCK.508-SST-M12-FKM-PC-P-E-NC	508	545	437	12.5	508±0.5	12	466
118349	HCK.508-SST-M12-FKM-PC-P-E-NO	508	545	437	12.5	508±0.5	12	466
118353	HCK.508-SST-M12-FKM-PC-P-E-SW	508	545	437	12.5	508±0.5	12	466
113461	HCK.127-SST-M12-FKM-PC-P-E-HT-NC	127	164	437	12.5	127±0.5	12	231
113459	HCK.127-SST-M12-FKM-PC-P-E-HT-NO	127	164	437	12.5	127±0.5	12	231
113463	HCK.127-SST-M12-FKM-PC-P-E-HT-SW	127	164	437	12.5	127±0.5	12	231
114439	HCK.176-SST-M12-FKM-PC-P-E-HT-NC	176	213	437	12.5	176±0.5	12	261
114437	HCK.176-SST-M12-FKM-PC-P-E-HT-NO	176	213	437	12.5	176±0.5	12	261
114441	HCK.176-SST-M12-FKM-PC-P-E-HT-SW	176	213	437	12.5	176±0.5	12	261
116549	HCK.254-SST-M12-FKM-PC-P-E-HT-NC	254	291	437	12.5	254±0.5	12	309
116547	HCK.254-SST-M12-FKM-PC-P-E-HT-NO	254	291	437	12.5	254±0.5	12	309
116551	HCK.254-SST-M12-FKM-PC-P-E-HT-SW	254	291	437	12.5	254±0.5	12	309
117459	HCK.381-SST-M12-FKM-PC-P-E-HT-NC	381	418	437	12.5	381±0.5	12	388
117457	HCK.381-SST-M12-FKM-PC-P-E-HT-NO	381	418	437	12.5	381±0.5	12	388
117461	HCK.381-SST-M12-FKM-PC-P-E-HT-SW	381	418	437	12.5	381±0.5	12	388
118369	HCK.508-SST-M12-FKM-PC-P-E-HT-NC	508	545	437	12.5	508±0.5	12	466
118367	HCK.508-SST-M12-FKM-PC-P-E-HT-NO	508	545	437	12.5	508±0.5	12	466
118371	HCK.508-SST-M12-FKM-PC-P-E-HT-SW	508	545	437	12.5	508±0.5	12	466
113355	HCK.127-SST-M12-NBR-GL-P-E-NC	127	164	437	12.5	127±0.5	12	231
113353	HCK.127-SST-M12-NBR-GL-P-E-NO	127	164	437	12.5	127±0.5	12	231
113357	HCK.127-SST-M12-NBR-GL-P-E-SW	127	164	437	12.5	127±0.5	12	231
114325	HCK.176-SST-M12-NBR-GL-P-E-NC	176	213	437	12.5	176±0.5	12	261
114323	HCK.176-SST-M12-NBR-GL-P-E-NO	176	213	437	12.5	176±0.5	12	261
114327	HCK.176-SST-M12-NBR-GL-P-E-SW	176	213	437	12.5	176±0.5	12	261
116435	HCK.254-SST-M12-NBR-GL-P-E-NC	254	291	437	12.5	254±0.5	12	309
116433	HCK.254-SST-M12-NBR-GL-P-E-NO	254	291	437	12.5	254±0.5	12	309
116437	HCK.254-SST-M12-NBR-GL-P-E-SW	254	291	437	12.5	254±0.5	12	309
117345	HCK.381-SST-M12-NBR-GL-P-E-NC	381	418	437	12.5	381±0.5	12	388
117343	HCK.381-SST-M12-NBR-GL-P-E-NO	381	418	437	12.5	381±0.5	12	388
117347	HCK.381-SST-M12-NBR-GL-P-E-SW	381	418	437	12.5	381±0.5	12	388
118255	HCK.508-SST-M12-NBR-GL-P-E-NC	508	545	437	12.5	508±0.5	12	466
118253	HCK.508-SST-M12-NBR-GL-P-E-NO	508	545	437	12.5	508±0.5	12	466
118257	HCK.508-SST-M12-NBR-GL-P-E-SW	508	545	437	12.5	508±0.5	12	466
113485	HCK.127-SST-M12-FKM-GL-P-E-NC	127	164	437	12.5	127±0.5	12	231
113483	HCK.127-SST-M12-FKM-GL-P-E-NO	127	164	437	12.5	127±0.5	12	231
113487	HCK.127-SST-M12-FKM-GL-P-E-SW	127	164	437	12.5	127±0.5	12	231
114463	HCK.176-SST-M12-FKM-GL-P-E-NC	176	213	437	12.5	176±0.5	12	261
114461	HCK.176-SST-M12-FKM-GL-P-E-NO	176	213	437	12.5	176±0.5	12	261
114465	HCK.176-SST-M12-FKM-GL-P-E-SW	176	213	437	12.5	176±0.5	12	261
116573	HCK.254-SST-M12-FKM-GL-P-E-NC	254	291	437	12.5	254±0.5	12	309
116571	HCK.254-SST-M12-FKM-GL-P-E-NO	254	291	437	12.5	254±0.5	12	309
116575	HCK.254-SST-M12-FKM-GL-P-E-SW	254	291	437	12.5	254±0.5	12	309
117483	HCK.381-SST-M12-FKM-GL-P-E-NC	381	418	437	12.5	381±0.5	12	388
117481	HCK.381-SST-M12-FKM-GL-P-E-NO	381	418	437	12.5	381±0.5	12	388
117485	HCK.381-SST-M12-FKM-GL-P-E-SW	381	418	437	12.5	381±0.5	12	388
118393	HCK.508-SST-M12-FKM-GL-P-E-NC	508	545	437	12.5	508±0.5	12	466
118391	HCK.508-SST-M12-FKM-GL-P-E-NO	508	545	437	12.5	508±0.5	12	466
118395	HCK.508-SST-M12-FKM-GL-P-E-SW	508	545	437	12.5	508±0.5	12	466
113503	HCK.127-SST-M12-FKM-GL-P-E-HT-NC	127	164	437	12.5	127±0.5	12	231
113501	HCK.127-SST-M12-FKM-GL-P-E-HT-NO	127	164	437	12.5	127±0.5	12	231
113505	HCK.127-SST-M12-FKM-GL-P-E-HT-SW	127	164	437	12.5	127±0.5	12	231
114481	HCK.176-SST-M12-FKM-GL-P-E-HT-NC	176	213	437	12.5	176±0.5	12	261
114479	HCK.176-SST-M12-FKM-GL-P-E-HT-NO	176	213	437	12.5	176±0.5	12	261
114483	HCK.176-SST-M12-FKM-GL-P-E-HT-SW	176	213	437	12.5	176±0.5	12	261
116591	HCK.254-SST-M12-FKM-GL-P-E-HT-NC	254	291	437	12.5	254±0.5	12	309
116589	HCK.254-SST-M12-FKM-GL-P-E-HT-NO	254	291	437	12.5	254±0.5	12	309
116593	HCK.254-SST-M12-FKM-GL-P-E-HT-SW	254	291	437	12.5	254±0.5	12	309
117501	HCK.381-SST-M12-FKM-GL-P-E-HT-NC	381	418	437	12.5	381±0.5	12	388
117499	HCK.381-SST-M12-FKM-GL-P-E-HT-NO	381	418	437	12.5	381±0.5	12	388
117503	HCK.381-SST-M12-FKM-GL-P-E-HT-SW	381	418	437	12.5	381±0.5	12	388
118411	HCK.508-SST-M12-FKM-GL-P-E-HT-NC	508	545	437	12.5	508±0.5	12	466
118409	HCK.508-SST-M12-FKM-GL-P-E-HT-NO	508	545	437	12.5	508±0.5	12	466
118413	HCK.508-SST-M12-FKM-GL-P-E-HT-SW	508	545	437	12.5	508±0.5	12	466

# zui大拧紧扭矩。

* See table for the configuration of the standard executions.

产品简介